AQA GCSE Design and Technology (DT) - Designing and Making - Market Research This resource contains all of the key knowledge that the students are required to know for Designing and Making - Market Research Market Research Target Market Questionnaires Open/Closed Questions Interviews Focus Groups The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students clarity and confidence in preparation for both the NEA and the written exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with the tracker (available for free) designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity, *(particularly effective when used with the tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enhanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on the tracker (available for free). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Designing and Making - Using Materials Efficiently This resource contains all of the key knowledge that the students are required to know for Designing and Making - Using Materials Efficiently Prototypes Efficient Use of Materials Waste Marking Out Tools Nesting Calculating Waste Safety The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students clarity and confidence in preparation for both the NEA and the written exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with the tracker (available for free) designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity, *(particularly effective when used with the tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enhanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on the tracker (available for free). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Designing and Making - Understanding User Needs This resource contains all of the key knowledge that the students are required to know for Designing and Making - Understanding User Needs Ergonomics Anthropometric Data 5th and 95th Percentile Accessible Design Designing for Children Designing for the Elderly The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students clarity and confidence in preparation for both the NEA and the written exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with the tracker (available for free) designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity, *(particularly effective when used with the tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enhanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on the tracker (available for free). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.1 - Uses of Woods, Metals and Polymers This resource contains all of the key knowledge that the students are required to know for Section 5.1 - Uses of Woods, Metals and Polymers Choosing Materials for Specific Purposes Modifications Wood (Timber) Seasoning Annealing UV Treatment The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 2.1 - Properties of Materials This resource contains all of the key knowledge that the students are required to know for Section 2.1 - Properties of Materials Working Properties Strength Hardness Toughness Elasticity Malleability Ductility Physical Properties Electrical Conductivity Thermal Conductivity Fusibility Density Absorbency Ferrous Non-Ferrous Alloys The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Designing and Making - Looking at the Work of Designers This resource contains all of the key knowledge that the students are required to know for Designing and Making - Looking at the Work of Designers The Work of Designers Fashion Designers Product Designers Graphic Designers Architects The Work of Companies Fashion Companies Product Design Companies The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students clarity and confidence in preparation for both the NEA and the written exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with the tracker (available for free) designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity, *(particularly effective when used with the tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enhanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on the tracker (available for free). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 3.4 - Quality Control This resource contains all of the key knowledge that the students are required to know for Section 3.4 - Quality Control Quality Control Tolerance Go/No Go Fixtures Registration Marks Depth Stops PCB Exposure Laser Cutter Programming The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 4.4 - Printing Techniques This resource contains all of the key knowledge that the students are required to know for Section 4.4 - Printing Techniques Lithography Offset Lithography Flexography Screen Printing Digital Printing CMYK Product Uses The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.4 - Shaping Materials (Hand Tools) This resource contains all of the key knowledge that the students are required to know for Section 5.4 - Shaping Materials (Hand Tools) Saws Rip Saw, Tenon Saw, Coping Saw, Hacksaw Chisels Plane File Abrasive Paper Drilling Bradawl Centre Punch Twist Bit Flat Bit Countersink Bit Hole Saw The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 3.5 - Production Aids This resource contains all of the key knowledge that the students are required to know for Section 3.5 - Production Aids Production Aids Reference Point Datum Scaling Template Pattern Jigs The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 3.1 - Selecting Materials This resource contains all of the key knowledge that the students are required to know for Section 3.1 - Selecting Materials Factors Affecting Material Choice Availability Functionality Aesthetics Material Cost Environmental Factors Social Factors Ethical Factors Cultural Factors The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 1.2 - Production Systems - CADCAM This resource contains all of the key knowledge that the students are required to know for Section 1.2 - Production Systems - CADCAM CAD CAM CNC Subtraction of Material Addition of Material 2-Axis CAM 3-Axis CAM Global Communication The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 1.5 - Products in Society This resource contains all of the key knowledge that the students are required to know for Section 1.5 - Products in Society Enterprise Crowdfunding Virtual Marketing Co-operatives Fairtrade Market Pull Technology Push Culture New Technology Design for Particular Groups The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.6 - Shaping Techniques This resource contains all of the key knowledge that the students are required to know for Section 5.6 - Shaping Techniques Shaping Techniques Milling Machines Lathes 3D Printing Metal Press Casting Die Casting Bending Materials Plywood Forming Line Bender Strip Heater Annealing The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 1.6 - Powering Systems This resource contains all of the key knowledge that the students are required to know for Section 1.6 - Powering Systems Fossil Fuels Finite Resources Non-Finite Resources Nuclear Power Renewable Energy Wind Power Solar Power Hydro-electric Power Tidal Barrages Biomass Arguments For and Against Renewable Energy Batteries The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.7 - Moulding and Joining This resource contains all of the key knowledge that the students are required to know for Section 5.7 - Moulding and Joining Vacuum Forming Blow Moulding Injection Moulding Extrusion Gluing Soldering Brazing Welding The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 3.3 - Scales of Production This resource contains all of the key knowledge that the students are required to know for Section 3.3 - Scales of Production Scale of Production One-off Production Batch Production Templates, Jigs and Moulds Mass Production Continuous Production Automation The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.5 - Shaping Materials (Power and Machine Tools) This resource contains all of the key knowledge that the students are required to know for Section 5.5 - Shaping Materials (Power and Machine Tools) Safety Steps Power Tools Router Planer Jigsaw Sander Machine Tools Sanding Disc Saw Bench Bandsaw Pillar Drill Fences The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.8 - Treatments and Finishes This resource contains all of the key knowledge that the students are required to know for Section 5.8 - Treatments and Finishes Painting Varnishing Tanalising Metal Finishing Dip Coating Powder Coating Galvanising Plastic Vinyl The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course

AQA GCSE Design and Technology (DT) - Exam Theory - Section 2.8 - Developments in New Materials This resource contains all of the key knowledge that the students are required to know for Section 2.8 - Developments in New Materials Modern Materials Graphene Metal Foams Titanium Liquid Crystal Displays (LCDs) Nanomaterials Smart Materials Shape Memory Alloys Photochromic Thermochromic Composites Glass Reinforced Plastic Carbon Fibre Technical Textiles Kevlar Nomex Micro Encapsulation The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam. These resources have been developed with the following goals in mind: Allows learners to work through the theory independently, promoting challenge for all learners and ability levels Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning. Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources. Allows independent home learning to be set that follows on and links clearly with the classwork. Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker) Suggested strategy: This resource is one sub-section. When used as a complete section the following strategy can be adopted: Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube. Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc. At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam. When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top). The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge. These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course